9 Second Chip Fix

Fiberglass boat damage? Here’s the smart way to patch chips, gouges, and drill holes like a pro.

9 Second Chip Fix is a super-tough, pre-coloured filler that repairs, colours, and seals fibreglass and gelcoat damage in one application. Nanotechnology deeply penetrates the damage to deliver industrial grade adhesion. It’s highly elastic too so it absorbs shock and helps prevent further damage.

• Long lasting repairs.
• Easy to use.
• Highly versatile 

• FIXES: Holes, chips, cracks, and gouges over 1mm. For fine cracks and scratches use Hairline Fix instead.
• WORKS ON:Fiberglass, acrylic, porcelain, enamel, ceramic, wood, carbon fibre, dry wall,ceramic, and stone.
  
• FINISH:Matte. For a gloss finish, apply a topcoat of Hairline Fix
• USE IT EVERYWHERE: Boat, jet ski, shower, tub, sink, tiles countertop, porcelain, acrylic, enamel and stone.
• ULTRA STRONG NANOTECHNOLOGY
• 60-day Customer Satisfaction Money Back Guarantee.

For fine cracks and scratches use Hairline Fix instead.

Available in 4 popular colours:

• Snow White
• Oyster White
• Matterhorn White
• Midnight

Colour Disclaimer

Actual colours may vary slightly from what you see on your screen due to factors like device settings, light conditions and individual light perception. For recommendations, please contact us via email or telephone. Please note any colour recommendations we provide are based on the information you share with us.

• Water soluble, one-part epoxy.
• UV and water resistant (above the waterline use only).
• High fill-rate / minimal slump.
• Can be applied to vertical surfaces.
• Can be sanded and drilled.
• No primer required.
• Suitable for use at temperatures above 70°F / 20°C.
• In cool temperatures use a hairdryer to set for 2 minutes.
• Vol. 12.9ml / 0.43 fl oz.

1. Using a needle or pin remove dirt and grime from the affected area.
2. For quality fibreglass repair and general fibreglass repair,scrub soapy water into the affected area to remove any further dirt and grime Rinse and fully dry.
3. Knead and shake tube/s for 2 minutes.
4. Slightly overfill the affected area with 9 Second Chip Fix.
5. Gently level the repair with the end of the tube.
6. Immediately remove smears and clean LEVEL with a damp tissue. Repeat if necessary.

Wet Areas:

Seal after 1 hour with clear sticky/scotch/cello tape for 14 days.

Deep Damage:

Repeat 2 or 3 times, every 2 hours.

• Download

How much damage can it repair?
MagicEzy 9 Second Chip Fix is suitable as a filler for chips and gouges over 1mm in width up to 4mm deep. For smaller damage (fine cracks and scratches) use Hairline Fix instead.

One tube will repair 15-20 5mm (diameter) x 3mm (deep) chips.

What surfaces will it work on?
As well as fiberglass you can also use it to repair ceramic, porcelain, acrylic, wood, enamel, dry wall, and stone surfaces.

Do I need to prime the surface first?
9 Second Chip Fix will adhere to fiberglass without a primer. For plastic or aluminum surfaces or to strengthen weakened fiberglass, apply a coat of MagicEzy Mega Fusion primer first.

Will it repair hull damage?
The product will professionally repair areas that are above the waterline.

You have a lot of whites to choose from. How do I select the right one?
It’s difficult to provide accurate color recommendations, but I can describe our white colors to help you make a choice.

• Snow White (RAL 9003) is a clean, pure white (Our brightest and best-selling white)

• Oyster White (RAL 9010) is a creamy off-white

• Matterhorn White (RAL 9002) is an off-white with a slight grey tone.

Can I add other tints or colorants to the product to achieve a color match?
No. Mixing additional products compromises the adhesion and effectiveness of MagicEzy products. We do not guarantee any products that have been mixed with other additives. However, two of our products can be mixed together.

Does the color dry lighter or darker than the color on the swatch?
The product is the same color wet or dry. When selecting colors note that the appearance of colors vary depending on the computer screen. If you’re not sure, buy one of our kits so you can blend colors to suit.

How long does it take to dry?
In temperatures over 20°C / 70°F, our repairs are already extremely strong within 24 to 48 hours.

Does it dry in gloss or matte finish?
9 Second Chip Fix dries in a matte finish.

Can I sand the product once dried?
Yes, however, there’s no need to sand the repair itself. Simply use the end of the tube to create a level repair. If you do want to sand the surface, please allow 7 days for the product to fully cure before sanding.

Can I paint over the product?
Yes, with water-based paints.

How do I store the tube once opened?
We suggest that you store the remaining product in the refrigerator.

What if I am not satisfied with the results?
All MagicEzy products come with a MONEY-BACK guarantee.

Simply return it to us (with the receipt) within 60 days, and we’ll provide a full refund or replacement.